Vulnerabilities (CVE)

Filtered by vendor Juniper Subscribe
CVE Vendors Products Updated CVSS v2 CVSS v3
CVE-2019-0015 1 Juniper 22 Junos, Srx100, Srx110 and 19 more 2021-11-09 5.5 MEDIUM 5.4 MEDIUM
A vulnerability in the SRX Series Service Gateway allows deleted dynamic VPN users to establish dynamic VPN connections until the device is rebooted. A deleted dynamic VPN connection should be immediately disallowed from establishing new VPN connections. Due to an error in token caching, deleted users are allowed to connect once a previously successful dynamic VPN connection has been established. A reboot is required to clear the cached authentication token. Affected releases are Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D75; 15.1X49 versions prior to 15.1X49-D150; 17.3 versions prior to 17.3R3; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R3; 18.2 versions prior to 18.2R2.
CVE-2019-0005 1 Juniper 14 Ex2300, Ex2300-c, Ex3400 and 11 more 2021-11-09 5.0 MEDIUM 5.3 MEDIUM
On EX2300, EX3400, EX4600, QFX3K and QFX5K series, firewall filter configuration cannot perform packet matching on any IPv6 extension headers. This issue may allow IPv6 packets that should have been blocked to be forwarded. IPv4 packet filtering is unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS on EX and QFX series;: 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1R7; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 series; 15.1X53 versions prior to 15.1X53-D591 on EX2300/EX3400 series; 16.1 versions prior to 16.1R7; 17.1 versions prior to 17.1R2-S10, 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R2.
CVE-2018-0063 1 Juniper 1 Junos 2021-11-06 3.3 LOW 6.5 MEDIUM
A vulnerability in the IP next-hop index database in Junos OS 17.3R3 may allow a flood of ARP requests, sent to the management interface, to exhaust the private Internal routing interfaces (IRIs) next-hop limit. Once the IRI next-hop database is full, no further next hops can be learned and existing entries cannot be cleared, leading to a sustained denial of service (DoS) condition. An indicator of compromise for this issue is the report of the following error message: %KERN-4: Nexthop index allocation failed: private index space exhausted This issue only affects the management interface, and does not impact regular transit traffic through the FPCs. This issue also only affects Junos OS 17.3R3. No prior versions of Junos OS are affected by this issue. Affected releases are Juniper Networks Junos OS: 17.3R3.
CVE-2019-0042 1 Juniper 1 Identity Management Service 2021-10-28 1.9 LOW 4.2 MEDIUM
Juniper Identity Management Service (JIMS) for Windows versions prior to 1.1.4 may send an incorrect message to associated SRX services gateways. This may allow an attacker with physical access to an existing domain connected Windows system to bypass SRX firewall policies, or trigger a Denial of Service (DoS) condition for the network.
CVE-2021-31373 1 Juniper 28 Junos, Srx100, Srx110 and 25 more 2021-10-27 3.5 LOW 5.4 MEDIUM
A persistent Cross-Site Scripting (XSS) vulnerability in Juniper Networks Junos OS on SRX Series, J-Web interface may allow a remote authenticated user to inject persistent and malicious scripts. An attacker can exploit this vulnerability to steal sensitive data and credentials from a web administration session, or hijack another user's active session to perform administrative actions. This issue affects: Juniper Networks Junos OS on SRX Series: 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S8; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R2-S1, 20.3R3.
CVE-2021-31364 1 Juniper 14 Junos, Srx1500, Srx300 and 11 more 2021-10-27 4.3 MEDIUM 5.9 MEDIUM
An Improper Check for Unusual or Exceptional Conditions vulnerability combined with a Race Condition in the flow daemon (flowd) of Juniper Networks Junos OS on SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2 allows an unauthenticated network based attacker sending specific traffic to cause a crash of the flowd/srxpfe process, responsible for traffic forwarding in SRX, which will cause a Denial of Service (DoS). Continued receipt and processing of this specific traffic will create a sustained Denial of Service (DoS) condition. This issue can only occur when specific packets are trying to create the same session and logging for session-close is configured as a policy action. Affected platforms are: SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2. Not affected platforms are: SRX4000 Series, SRX5000 Series with SPC3, and vSRX Series. This issue affects Juniper Networks Junos OS SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2: All versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2.
CVE-2021-31369 1 Juniper 18 Junos, Mx10, Mx10000 and 15 more 2021-10-26 4.3 MEDIUM 5.3 MEDIUM
On MX Series platforms with MS-MPC/MS-MIC, an Allocation of Resources Without Limits or Throttling vulnerability in Juniper Networks Junos OS allows an unauthenticated network attacker to cause a partial Denial of Service (DoS) with a high rate of specific traffic. If a Class of Service (CoS) rule is attached to the service-set and a high rate of specific traffic is processed by this service-set, for some of the other traffic which has services applied and is being processed by this MS-MPC/MS-MIC drops will be observed. Continued receipted of this high rate of specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on MX Series with MS-MPC/MS-MIC: All versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2.
CVE-2021-31365 1 Juniper 5 Ex2300, Ex3400, Ex4300 and 2 more 2021-10-26 2.9 LOW 6.5 MEDIUM
An Uncontrolled Resource Consumption vulnerability in Juniper Networks Junos OS on EX2300, EX3400 and EX4300 Series platforms allows an adjacent attacker sending a stream of layer 2 frames will trigger an Aggregated Ethernet (AE) interface to go down and thereby causing a Denial of Service (DoS). By continuously sending a stream of specific layer 2 frames an attacker will sustain the Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS EX4300 Series All versions prior to 15.1R7-S7; 16.1 versions prior to 16.1R7-S8; 17.1 versions prior to 17.1R2-S12; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Juniper Networks Junos OS EX3400 and EX4300-MP Series All versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S9, 18.4R3-S7; 19.1 versions prior to 19.1R2-S3, 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2. Juniper Networks Junos OS EX2300 Series All versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R2.
CVE-2021-31352 1 Juniper 1 Session And Resource Control 2021-10-26 5.0 MEDIUM 5.3 MEDIUM
An Information Exposure vulnerability in Juniper Networks SRC Series devices configured for NETCONF over SSH permits the negotiation of weak ciphers, which could allow a remote attacker to obtain sensitive information. A remote attacker with read and write access to network data could exploit this vulnerability to display plaintext bits from a block of ciphertext and obtain sensitive information. This issue affects all Juniper Networks SRC Series versions prior to 4.13.0-R6.
CVE-2021-31355 1 Juniper 1 Junos 2021-10-25 3.5 LOW 5.4 MEDIUM
A persistent cross-site scripting (XSS) vulnerability in the captive portal graphical user interface of Juniper Networks Junos OS may allow a remote authenticated user to inject web script or HTML and steal sensitive data and credentials from a web administration session, possibly tricking a follow-on administrative user to perform administrative actions on the device. This issue affects Juniper Networks Junos OS: All versions, including the following supported releases: 12.3X48 versions prior to 12.3X48-D105; 15.1X49 versions prior to 15.1X49-D220; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R3-S3; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R3-S6; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R1-S1, 20.2R2; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2; 21.1 versions prior to 21.1R2.
CVE-2021-31370 1 Juniper 15 Ex4600, Ex4600-vc, Ex4650 and 12 more 2021-10-25 3.3 LOW 6.5 MEDIUM
An Incomplete List of Disallowed Inputs vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX5000 Series and EX4600 Series allows an adjacent unauthenticated attacker which sends a high rate of specific multicast traffic to cause control traffic received from the network to be dropped. This will impact control protocols (including but not limited to routing-protocols) and lead to a Denial of Service (DoS). Continued receipt of this specific multicast traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX5000 and EX4600 Series: All versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2.
CVE-2021-31361 1 Juniper 44 Junos, Ptx1000, Ptx1000-72q and 41 more 2021-10-25 5.0 MEDIUM 5.3 MEDIUM
An Improper Check for Unusual or Exceptional Conditions vulnerability combined with Improper Handling of Exceptional Conditions in Juniper Networks Junos OS on QFX Series and PTX Series allows an unauthenticated network based attacker to cause increased FPC CPU utilization by sending specific IP packets which are being VXLAN encapsulated leading to a partial Denial of Service (DoS). Continued receipted of these specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on QFX Series: All versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. Juniper Networks Junos OS on PTX Series: All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2.
CVE-2021-31362 1 Juniper 2 Junos, Junos Os Evolved 2021-10-25 3.3 LOW 6.5 MEDIUM
A Protection Mechanism Failure vulnerability in RPD (routing protocol daemon) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent unauthenticated attacker to cause established IS-IS adjacencies to go down by sending a spoofed hello PDU leading to a Denial of Service (DoS) condition. Continued receipted of these spoofed PDUs will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS All versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R2-EVO; 21.1 versions prior to 21.1R2-EVO.
CVE-2021-31380 1 Juniper 1 Session And Resource Control 2021-10-25 5.0 MEDIUM 5.3 MEDIUM
A configuration weakness in the JBoss Application Server (AppSvr) component of Juniper Networks SRC Series allows a remote attacker to send a specially crafted query to cause the web server to disclose sensitive information in the HTTP response which allows the attacker to obtain sensitive information.
CVE-2021-31386 1 Juniper 1 Junos 2021-10-25 2.6 LOW 5.9 MEDIUM
A Protection Mechanism Failure vulnerability in the J-Web HTTP service of Juniper Networks Junos OS allows a remote unauthenticated attacker to perform Person-in-the-Middle (PitM) attacks against the device. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S20; 15.1 versions prior to 15.1R7-S11; 18.3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R3-S10; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R2.
CVE-2021-31363 1 Juniper 2 Junos, Junos Os Evolved 2021-10-25 3.3 LOW 6.5 MEDIUM
In an MPLS P2MP environment a Loop with Unreachable Exit Condition vulnerability in the routing protocol daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated adjacent attacker to cause high load on RPD which in turn may lead to routing protocol flaps. If a system with sensor-based-stats enabled receives a specific LDP FEC this can lead to the above condition. Continued receipted of such an LDP FEC will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 19.2 version 19.2R2 and later versions prior to 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 19.2R2. Juniper Networks Junos OS Evolved All versions prior to 20.1R2-S3-EVO; 20.3 versions prior to 20.3R1-S2-EVO.
CVE-2021-31377 1 Juniper 1 Junos 2021-10-25 2.1 LOW 5.5 MEDIUM
An Incorrect Permission Assignment for Critical Resource vulnerability of a certain file in the filesystem of Junos OS allows a local authenticated attacker to cause routing process daemon (RPD) to crash and restart, causing a Denial of Service (DoS). Repeated actions by the attacker will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S7; 19.1 versions prior to 19.1R2-S3, 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R1-S1, 20.4R2.
CVE-2019-0038 1 Juniper 3 Junos, Srx340, Srx345 2021-10-25 6.1 MEDIUM 6.5 MEDIUM
Crafted packets destined to the management interface (fxp0) of an SRX340 or SRX345 services gateway may create a denial of service (DoS) condition due to buffer space exhaustion. This issue only affects the SRX340 and SRX345 services gateways. No other products or platforms are affected by this vulnerability. Affected releases are Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D160 on SRX340/SRX345; 17.3 on SRX340/SRX345; 17.4 versions prior to 17.4R2-S3, 17.4R3 on SRX340/SRX345; 18.1 versions prior to 18.1R3-S1 on SRX340/SRX345; 18.2 versions prior to 18.2R2 on SRX340/SRX345; 18.3 versions prior to 18.3R1-S2, 18.3R2 on SRX340/SRX345. This issue does not affect Junos OS releases prior to 15.1X49 on any platform.
CVE-2021-31375 1 Juniper 1 Junos 2021-10-25 5.0 MEDIUM 5.3 MEDIUM
An Improper Input Validation vulnerability in routing process daemon (RPD) of Juniper Networks Junos OS devices configured with BGP origin validation using Resource Public Key Infrastructure (RPKI), allows an attacker to send a specific BGP update which may cause RPKI policy-checks to be bypassed. This, in turn, may allow a spoofed advertisement to be accepted or propagated. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S18; 15.1 versions prior to 15.1R7-S9; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R3-S1; 18.4 versions prior to 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R2.
CVE-2021-31366 1 Juniper 17 Junos, Mx10, Mx10003 and 14 more 2021-10-25 3.3 LOW 6.5 MEDIUM
An Unchecked Return Value vulnerability in the authd (authentication daemon) of Juniper Networks Junos OS on MX Series configured for subscriber management / BBE allows an adjacent attacker to cause a crash by sending a specific username. This impacts authentication, authorization, and accounting (AAA) services on the MX devices and leads to a Denial of Service (DoS) condition. Continued receipted of these PPP login request will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2.
CVE-2021-0287 1 Juniper 2 Junos, Junos Os Evolved 2021-10-25 5.7 MEDIUM 6.5 MEDIUM
In a Segment Routing ISIS (SR-ISIS)/MPLS environment, on Juniper Networks Junos OS and Junos OS Evolved devices, configured with ISIS Flexible Algorithm for Segment Routing and sensor-based statistics, a flap of a ISIS link in the network, can lead to a routing process daemon (RPD) crash and restart, causing a Denial of Service (DoS). Continued link flaps will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 19.4 versions prior to 19.4R1-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R2; Juniper Networks Junos OS Evolved: 20.3-EVO versions prior to 20.3R2-EVO; 20.4-EVO versions prior to 20.4R2-EVO. This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.
CVE-2020-1681 1 Juniper 1 Junos Os Evolved 2021-10-25 3.3 LOW 6.5 MEDIUM
Receipt of a specifically malformed NDP packet sent from the local area network (LAN) to a device running Juniper Networks Junos OS Evolved can cause the ndp process to crash, resulting in a Denial of Service (DoS). The process automatically restarts without intervention, but a continuous receipt of the malformed NDP packets could leaded to an extended Denial of Service condition. During this time, IPv6 neighbor learning will be affected. The issue occurs when parsing the incoming malformed NDP packet. Rather than simply discarding the packet, the process asserts, performing a controlled exit and restart, thereby avoiding any chance of an unhandled exception. Exploitation of this vulnerability is limited to a temporary denial of service, and cannot be leveraged to cause additional impact on the system. This issue is limited to the processing of IPv6 NDP packets. IPv4 packet processing cannot trigger, and is unaffected by this vulnerability. This issue affects all Juniper Networks Junos OS Evolved versions prior to 20.1R2-EVO. Junos OS is unaffected by this vulnerability.
CVE-2020-1666 1 Juniper 1 Junos Os Evolved 2021-10-25 7.2 HIGH 6.6 MEDIUM
The system console configuration option 'log-out-on-disconnect' In Juniper Networks Junos OS Evolved fails to log out an active CLI session when the console cable is disconnected. This could allow a malicious attacker with physical access to the console the ability to resume a previous interactive session and possibly gain administrative privileges. This issue affects all Juniper Networks Junos OS Evolved versions after 18.4R1-EVO, prior to 20.2R1-EVO.
CVE-2021-0297 1 Juniper 1 Junos Os Evolved 2021-10-25 6.4 MEDIUM 6.5 MEDIUM
A vulnerability in the processing of TCP MD5 authentication in Juniper Networks Junos OS Evolved may allow a BGP or LDP session configured with MD5 authentication to succeed, even if the peer does not have TCP MD5 authentication enabled. This could lead to untrusted or unauthorized sessions being established, resulting in an impact on confidentiality or stability of the network. This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.3R2-S1-EVO; 20.4 versions prior to 20.4R2-EVO; 21.1 versions prior to 21.1R2-EVO. Juniper Networks Junos OS is not affected by this issue.
CVE-2020-1678 1 Juniper 2 Junos, Junos Os Evolved 2021-10-25 2.9 LOW 6.5 MEDIUM
On Juniper Networks Junos OS and Junos OS Evolved platforms with EVPN configured, receipt of specific BGP packets causes a slow memory leak. If the memory is exhausted the rpd process might crash. If the issue occurs, the memory leak could be seen by executing the "show task memory detail | match policy | match evpn" command multiple times to check if memory (Alloc Blocks value) is increasing. root@device> show task memory detail | match policy | match evpn ------------------------ Allocator Memory Report ------------------------ Name | Size | Alloc DTXP Size | Alloc Blocks | Alloc Bytes | MaxAlloc Blocks | MaxAlloc Bytes Policy EVPN Params 20 24 3330678 79936272 3330678 79936272 root@device> show task memory detail | match policy | match evpn ------------------------ Allocator Memory Report ------------------------ Name | Size | Alloc DTXP Size | Alloc Blocks | Alloc Bytes | MaxAlloc Blocks | MaxAlloc Bytes Policy EVPN Params 20 24 36620255 878886120 36620255 878886120 This issue affects: Juniper Networks Junos OS 19.4 versions prior to 19.4R2; 20.1 versions prior to 20.1R1-S4, 20.1R2; Juniper Networks Junos OS Evolved: 19.4 versions; 20.1 versions prior to 20.1R1-S4-EVO, 20.1R2-EVO; 20.2 versions prior to 20.2R1-EVO; This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.
CVE-2021-0292 1 Juniper 1 Junos Os Evolved 2021-10-25 3.3 LOW 6.5 MEDIUM
An Uncontrolled Resource Consumption vulnerability in the ARP daemon (arpd) and Network Discovery Protocol (ndp) process of Juniper Networks Junos OS Evolved allows a malicious attacker on the local network to consume memory resources, ultimately resulting in a Denial of Service (DoS) condition. Link-layer functions such as IPv4 and/or IPv6 address resolution may be impacted, leading to traffic loss. The processes do not recover on their own and must be manually restarted. Changes in memory usage can be monitored using the following shell commands (header shown for clarity): user@router:/var/log# ps aux | grep arpd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 31418 59.0 0.7 *5702564* 247952 ? xxx /usr/sbin/arpd --app-name arpd -I object_select --shared-objects-mode 3 user@router:/var/log# ps aux | grep arpd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 31418 49.1 1.0 *5813156* 351184 ? xxx /usr/sbin/arpd --app-name arpd -I object_select --shared-objects-mode 3 Memory usage can be monitored for the ndp process in a similar fashion: user@router:/var/log# ps aux | grep ndp USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 14935 0.0 0.1 *5614052* 27256 ? Ssl Jun15 0:17 /usr/sbin/ndp -I no_tab_chk,object_select --app-name ndp --shared-obje user@router:/var/log# ps aux | grep ndp USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 14935 0.0 0.1 *5725164* 27256 ? Ssl Jun15 0:17 /usr/sbin/ndp -I no_tab_chk,object_select --app-name ndp --shared-obje This issue affects Juniper Networks Junos OS Evolved: 19.4 versions prior to 19.4R2-S3-EVO; 20.1 versions prior to 20.1R2-S4-EVO; all versions of 20.2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 19.4R2-EVO.
CVE-2021-0209 1 Juniper 1 Junos Os Evolved 2021-10-25 5.7 MEDIUM 6.5 MEDIUM
In Juniper Networks Junos OS Evolved an attacker sending certain valid BGP update packets may cause Junos OS Evolved to access an uninitialized pointer causing RPD to core leading to a Denial of Service (DoS). Continued receipt of these types of valid BGP update packets will cause an extended Denial of Service condition. RPD will require a restart to recover. An indicator of compromise is to see if the file rpd.re exists by issuing the command: show system core-dumps This issue affects: Juniper Networks Junos OS Evolved 19.4 versions prior to 19.4R2-S2-EVO; 20.1 versions prior to 20.1R1-S2-EVO, 20.1R2-S1-EVO. This issue does not affect Junos OS.
CVE-2021-31367 1 Juniper 10 Junos, Ptx1000, Ptx10001-36mr and 7 more 2021-10-25 2.9 LOW 6.5 MEDIUM
A Missing Release of Memory after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on PTX Series allows an adjacent attacker to cause a Denial of Service (DoS) by sending genuine BGP flowspec packets which cause an FPC heap memory leak. Once having run out of memory the FPC will crash and restart along with a core dump. Continued receipted of these packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S6; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. Juniper Networks Junos Evolved is not affected.
CVE-2021-0298 1 Juniper 3 Junos Os Evolved, Ptx10003, Ptx10008 2021-10-25 4.0 MEDIUM 4.7 MEDIUM
A Race Condition in the 'show chassis pic' command in Juniper Networks Junos OS Evolved may allow an attacker to crash the port interface concentrator daemon (picd) process on the FPC, if the command is executed coincident with other system events outside the attacker's control, leading to a Denial of Service (DoS) condition. Continued execution of the CLI command, under precise conditions, could create a sustained Denial of Service (DoS) condition. This issue affects all Juniper Networks Junos OS Evolved versions prior to 20.1R2-EVO on PTX10003 and PTX10008 platforms. Junos OS is not affected by this vulnerability.
CVE-2020-1651 1 Juniper 16 Junos, Mx10, Mx10000 and 13 more 2021-10-19 3.3 LOW 6.5 MEDIUM
On Juniper Networks MX series, receipt of a stream of specific Layer 2 frames may cause a memory leak resulting in the packet forwarding engine (PFE) on the line card to crash and restart, causing traffic interruption. By continuously sending this stream of specific layer 2 frame, an attacker connected to the same broadcast domain can repeatedly crash the PFE, causing a prolonged Denial of Service (DoS). This issue affects Juniper Networks Junos OS on MX Series: 17.2 versions prior to 17.2R3-S4; 17.2X75 versions prior to 17.2X75-D105.19; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R1-S3, 17.4R2; 18.1 versions prior to 18.1R2. This issue does not affect Juniper Networks Junos OS releases prior to 17.2R1.
CVE-2021-39532 1 Juniper 1 Libslax 2021-10-02 4.3 MEDIUM 6.5 MEDIUM
An issue was discovered in libslax through v0.22.1. A NULL pointer dereference exists in the function slaxLexer() located in slaxlexer.c. It allows an attacker to cause Denial of Service.
CVE-2020-1625 1 Juniper 1 Junos 2021-09-14 3.3 LOW 6.5 MEDIUM
The kernel memory usage represented as "temp" via 'show system virtual-memory' may constantly increase when Integrated Routing and Bridging (IRB) is configured with multiple underlay physical interfaces, and one interface flaps. This memory leak can affect running daemons (processes), leading to an extended Denial of Service (DoS) condition. Usage of "temp" virtual memory, shown here by a constantly increasing value of outstanding Requests, can be monitored by executing the 'show system virtual-memory' command as shown below: user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 10551 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6460 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 16101 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6665 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 21867 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6858 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3; 18.2X75 versions prior to 18.2X75-D33, 18.2X75-D411, 18.2X75-D420, 18.2X75-D60; 18.3 versions prior to 18.3R1-S5, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R2-S2, 18.4R3; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2. This issue does not affect Juniper Networks Junos OS 12.3 and 15.1.
CVE-2020-1600 1 Juniper 1 Junos 2021-09-14 6.8 MEDIUM 6.5 MEDIUM
In a Point-to-Multipoint (P2MP) Label Switched Path (LSP) scenario, an uncontrolled resource consumption vulnerability in the Routing Protocol Daemon (RPD) in Juniper Networks Junos OS allows a specific SNMP request to trigger an infinite loop causing a high CPU usage Denial of Service (DoS) condition. This issue affects both SNMP over IPv4 and IPv6. This issue affects: Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D90; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D238, 15.1X53-D592; 16.1 versions prior to 16.1R7-S5; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R3-S1; 17.2 versions prior to 17.2R3-S2; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R2-S4, 17.4R3; 18.1 versions prior to 18.1R3-S5; 18.2 versions prior to 18.2R3; 18.2X75 versions prior to 18.2X75-D50; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2.
CVE-2021-0293 1 Juniper 1 Junos 2021-07-29 2.1 LOW 5.5 MEDIUM
A vulnerability in Juniper Networks Junos OS caused by Missing Release of Memory after Effective Lifetime leads to a memory leak each time the CLI command 'show system connections extensive' is executed. The amount of memory leaked on each execution depends on the number of TCP connections from and to the system. Repeated execution will cause more memory to leak and eventually daemons that need to allocate additionally memory and ultimately the kernel to crash, which will result in traffic loss. Continued execution of this command will cause a sustained Denial of Service (DoS) condition. An administrator can use the following CLI command to monitor for increase in memory consumption of the netstat process, if it exists: user@junos> show system processes extensive | match "username|netstat" PID USERNAME PRI NICE SIZE RES STATE C TIME WCPU COMMAND 21181 root 100 0 5458M 4913M CPU3 2 0:59 97.27% netstat The following log message might be observed if this issue happens: kernel: %KERN-3: pid 21181 (netstat), uid 0, was killed: out of swap space This issue affects Juniper Networks Junos OS 18.2 versions prior to 18.2R2-S8, 18.2R3-S7. 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; 19.4 versions prior to 19.4R1-S4, 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2; This issue does not affect Juniper Networks Junos OS versions prior to 18.2R1.
CVE-2021-0290 1 Juniper 26 Ex9200, Ex9204, Ex9208 and 23 more 2021-07-29 3.3 LOW 6.5 MEDIUM
Improper Handling of Exceptional Conditions in Ethernet interface frame processing of Juniper Networks Junos OS allows an attacker to send specially crafted frames over the local Ethernet segment, causing the interface to go into a down state, resulting in a Denial of Service (DoS) condition. The interface does not recover on its own and the FPC must be reset manually. Continued receipt and processing of these frames will create a sustained Denial of Service (DoS) condition. This issue is platform-specific and affects the following platforms and line cards: * MPC7E/8E/9E and MPC10E on MX240, MX480, MX960, MX2008, MX2010, and MX2020 * MX204, MX10003, MX10008, MX10016 * EX9200, EX9251 * SRX4600 No other products or platforms are affected by this vulnerability. An indication of this issue occurring can be seen in the system log messages, as shown below: user@host> show log messages | match "Failed to complete DFE tuning" fpc4 smic_phy_dfe_tuning_state: et-4/1/6 - Failed to complete DFE tuning (count 3) and interface will be in a permanently down state: user@host> show interfaces et-4/1/6 terse Interface Admin Link Proto Local Remote et-4/1/6 up down et-4/1/6.0 up down aenet --> ae101.0 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S7 on MX Series; 17.1R1 and later versions prior to 17.2R3-S3 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S11, 17.4R3-S1 on MX Series, SRX4600; 18.1 versions prior to 18.1R3-S10 on MX Series, EX9200 Series, SRX4600; 18.2 versions prior to 18.2R3-S3 on MX Series, EX9200 Series, SRX4600; 18.3 versions prior to 18.3R3-S1 on MX Series, EX9200 Series, SRX4600; 18.4 versions prior to 18.4R2-S3, 18.4R3 on MX Series, EX9200 Series, SRX4600; 19.1 versions prior to 19.1R2-S1, 19.1R3 on MX Series, EX9200 Series, SRX4600; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series, EX9200 Series, SRX4600; 19.3 versions prior to 19.3R2 on MX Series, EX9200 Series, SRX4600. This issue does not affect Juniper Networks Junos OS versions prior to 16.1R1.
CVE-2021-0288 1 Juniper 26 Ex9200, Ex9204, Ex9208 and 23 more 2021-07-29 3.3 LOW 6.5 MEDIUM
A vulnerability in the processing of specific MPLS packets in Juniper Networks Junos OS on MX Series and EX9200 Series devices with Trio-based MPCs (Modular Port Concentrators) may cause FPC to crash and lead to a Denial of Service (DoS) condition. Continued receipt of this packet will sustain the Denial of Service (DoS) condition. This issue only affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines). This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S8; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2;
CVE-2021-0295 1 Juniper 5 Junos, Qfx10000, Qfx10002 and 2 more 2021-07-28 2.9 LOW 6.1 MEDIUM
A vulnerability in the Distance Vector Multicast Routing Protocol (DVMRP) of Juniper Networks Junos OS on the QFX10K Series switches allows an attacker to trigger a packet forwarding loop, leading to a partial Denial of Service (DoS). The issue is caused by DVMRP packets looping on a multi-homed Ethernet Segment Identifier (ESI) when VXLAN is configured. DVMRP packets received on a multi-homed ESI are sent to the peer, and then incorrectly forwarded out the same ESI, violating the split horizon rule. This issue only affects QFX10K Series switches, including the QFX10002, QFX10008, and QFX10016. Other products and platforms are unaffected by this vulnerability. This issue affects Juniper Networks Junos OS on QFX10K Series: 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 version 18.2R1 and later versions; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S9, 18.4R3-S8; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S7, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2.
CVE-2021-0294 1 Juniper 8 Ex4600, Ex4650, Junos and 5 more 2021-07-28 5.0 MEDIUM 5.3 MEDIUM
A vulnerability in Juniper Networks Junos OS, which only affects the release 18.4R2-S5, where a function is inconsistently implemented on Juniper Networks Junos QFX5000 Series and EX4600 Series, and if "storm-control enhanced" is configured, can lead to the enhanced storm control filter group not be installed. It will cause storm control not to work hence allowing an attacker to cause high CPU usage or packet loss issues by sending a large amount of broadcast or unknown unicast packets arriving the device. This issue affects Juniper Networks QFX5100, QFX5110, QFX5120, QFX5200, QFX5210, EX4600, and EX4650, and QFX5100 with QFX 5e Series image installed. QFX5130 and QFX5220 are not affected from this issue. This issue affects Juniper Networks Junos OS 18.4R2-S5 on QFX5000 Series and EX4600 Series. No other product or platform is affected by this vulnerability.
CVE-2021-0289 1 Juniper 229 Acx1000, Acx1100, Acx2000 and 226 more 2021-07-28 2.9 LOW 5.3 MEDIUM
When user-defined ARP Policer is configured and applied on one or more Aggregated Ethernet (AE) interface units, a Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability between the Device Control Daemon (DCD) and firewall process (dfwd) daemons of Juniper Networks Junos OS allows an attacker to bypass the user-defined ARP Policer. In this particular case the User ARP policer is replaced with default ARP policer. To review the desired ARP Policers and actual state one can run the command "show interfaces <> extensive" and review the output. See further details below. An example output is: show interfaces extensive | match policer Policer: Input: __default_arp_policer__ <<< incorrect if user ARP Policer was applied on an AE interface and the default ARP Policer is displayed Policer: Input: jtac-arp-ae5.317-inet-arp <<< correct if user ARP Policer was applied on an AE interface For all platforms, except SRX Series: This issue affects Juniper Networks Junos OS: All versions 5.6R1 and all later versions prior to 18.4 versions prior to 18.4R2-S9, 18.4R3-S9 with the exception of 15.1 versions 15.1R7-S10 and later versions; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; This issue does not affect Juniper Networks Junos OS versions prior to 5.6R1. On SRX Series this issue affects Juniper Networks Junos OS: 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.4 versions prior to 19.4R3-S4; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect 18.4 versions prior to 18.4R1 on SRX Series. This issue does not affect Junos OS Evolved.
CVE-2021-0279 1 Juniper 1 Contrail Cloud 2021-07-27 5.5 MEDIUM 5.5 MEDIUM
Juniper Networks Contrail Cloud (CC) releases prior to 13.6.0 have RabbitMQ service enabled by default with hardcoded credentials. The messaging services of RabbitMQ are used when coordinating operations and status information among Contrail services. An attacker with access to an administrative service for RabbitMQ (e.g. GUI), can use these hardcoded credentials to cause a Denial of Service (DoS) or have access to unspecified sensitive system information. This issue affects the Juniper Networks Contrail Cloud releases on versions prior to 13.6.0.
CVE-2021-0271 1 Juniper 10 Ex2200-c, Ex3200, Ex3300 and 7 more 2021-07-23 3.3 LOW 6.5 MEDIUM
A Double Free vulnerability in the software forwarding interface daemon (sfid) process of Juniper Networks Junos OS allows an adjacently-connected attacker to cause a Denial of Service (DoS) by sending a crafted ARP packet to the device. Continued receipt and processing of the crafted ARP packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX2200-C Series, EX3200 Series, EX3300 Series, EX4200 Series, EX4500 Series, EX4550 Series, EX6210 Series, EX8208 Series, EX8216 Series. 12.3 versions prior to 12.3R12-S17; 15.1 versions prior to 15.1R7-S8. This issue only affects the listed Marvell-chipset based EX Series devices. No other products or platforms are affected.
CVE-2021-0267 1 Juniper 1 Junos 2021-07-23 3.3 LOW 6.5 MEDIUM
An Improper Input Validation vulnerability in the active-lease query portion in JDHCPD's DHCP Relay Agent of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) by sending a crafted DHCP packet to the device thereby crashing the jdhcpd DHCP service. This is typically configured for Broadband Subscriber Sessions. Continued receipt and processing of this crafted packet will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Junos OS Evolved.
CVE-2021-0241 1 Juniper 1 Junos 2021-07-23 3.3 LOW 6.5 MEDIUM
On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash with a core dump if a specific DHCPv6 packet is received, resulting in a restart of the daemon. The daemon automatically restarts without intervention, but continued receipt and processing of these specific packets will repeatedly crash the JDHCPD process and sustain the Denial of Service (DoS) condition. This issue only affects DHCPv6. DHCPv4 is not affected by this issue. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S7; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1, 19.3R3-S2; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2.
CVE-2021-0242 1 Juniper 2 Ex4300, Junos 2021-07-23 6.1 MEDIUM 6.5 MEDIUM
A vulnerability due to the improper handling of direct memory access (DMA) buffers on EX4300 switches on Juniper Networks Junos OS allows an attacker sending specific unicast frames to trigger a Denial of Service (DoS) condition by exhausting DMA buffers, causing the FPC to crash and the device to restart. The DMA buffer leak is seen when receiving these specific, valid unicast frames on an interface without Layer 2 Protocol Tunneling (L2PT) or dot1x configured. Interfaces with either L2PT or dot1x configured are not vulnerable to this issue. When this issue occurs, DMA buffer usage keeps increasing and the following error log messages may be observed: Apr 14 14:29:34.360 /kernel: pid 64476 (pfex_junos), uid 0: exited on signal 11 (core dumped) Apr 14 14:29:33.790 init: pfe-manager (PID 64476) terminated by signal number 11. Core dumped! The DMA buffers on the FPC can be monitored by the executing vty command 'show heap': ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 4a46000 268435456 238230496 30204960 11 Kernel 1 18a46000 67108864 17618536 49490328 73 Bcm_sdk 2 23737000 117440512 18414552 99025960 84 DMA buf <<<<< keeps increasing 3 2a737000 16777216 16777216 0 0 DMA desc This issue affects Juniper Networks Junos OS on the EX4300: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2.
CVE-2021-0240 1 Juniper 1 Junos 2021-07-23 2.9 LOW 6.5 MEDIUM
On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, the Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash if a malformed DHCPv6 packet is received, resulting in a restart of the daemon. The daemon automatically restarts without intervention, but continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects DHCPv6. DHCPv4 is not affected by this issue. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R3-S2; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2.
CVE-2021-0237 1 Juniper 11 Ex4300-mp, Ex4600, Ex4650 and 8 more 2021-07-23 3.3 LOW 6.5 MEDIUM
On Juniper Networks EX4300-MP Series, EX4600 Series, EX4650 Series, QFX5K Series deployed as a Virtual Chassis with a specific Layer 2 circuit configuration, Packet Forwarding Engine manager (FXPC) process may crash and restart upon receipt of specific layer 2 frames. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX4300-MP Series, EX4600 Series, EX4650 Series, QFX5K Series 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4, 17.4R3-S5; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2;
CVE-2021-0228 1 Juniper 11 Junos, Mx10, Mx104 and 8 more 2021-07-23 3.3 LOW 6.5 MEDIUM
An improper check for unusual or exceptional conditions vulnerability in Juniper Networks MX Series platforms with Trio-based MPC (Modular Port Concentrator) deployed in (Ethernet VPN) EVPN-(Virtual Extensible LAN) VXLAN configuration, may allow an attacker sending specific Layer 2 traffic to cause Distributed Denial of Service (DDoS) protection to trigger unexpectedly, resulting in traffic impact. Continued receipt and processing of this specific Layer 2 frames will sustain the Denial of Service (DoS) condition. An indication of compromise is to check DDOS LACP violations: user@device> show ddos-protection protocols statistics brief | match lacp This issue only affects the MX Series platforms with Trio-based MPC. No other products or platforms are affected. This issue affects: Juniper Networks Junos OS on MX Series: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2;
CVE-2021-0224 1 Juniper 1 Junos 2021-07-23 3.3 LOW 6.5 MEDIUM
A vulnerability in the handling of internal resources necessary to bring up a large number of Layer 2 broadband remote access subscriber (BRAS) nodes in Juniper Networks Junos OS can cause the Access Node Control Protocol daemon (ANCPD) to crash and restart, leading to a Denial of Service (DoS) condition. Continued processing of spoofed subscriber nodes will create a sustained Denial of Service (DoS) condition. When the number of subscribers attempting to connect exceeds the configured maximum-discovery-table-entries value, the subscriber fails to map to an internal neighbor entry, causing the ANCPD process to crash. This issue affects Juniper Networks Junos OS: All versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R3-S8; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R2.
CVE-2020-1641 1 Juniper 1 Junos 2021-07-23 3.3 LOW 6.5 MEDIUM
A Race Condition vulnerability in Juniper Networks Junos OS LLDP implementation allows an attacker to cause LLDP to crash leading to a Denial of Service (DoS). This issue occurs when crafted LLDP packets are received by the device from an adjacent device. Multiple LACP flaps will occur after LLDP crashes. An indicator of compromise is to evaluate log file details for lldp with RLIMIT. Intervention should occur before 85% threshold of used KB versus maximum available KB memory is reached. show log messages | match RLIMIT | match lldp | last 20 Matching statement is " /kernel: %KERNEL-[number]: Process ([pid #],lldpd) has exceeded 85% of RLIMIT_DATA: " with [] as variable data to evaluate for. This issue affects: Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S4, 17.4R3; 18.1 versions prior to 18.1R3-S5; 18.2 versions prior to 18.2R2-S7, 18.2R3; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D33, 18.2X75-D50, 18.2X75-D420; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S4, 19.1R2.
CVE-2020-1655 1 Juniper 16 Junos, Mx10, Mx10000 and 13 more 2021-07-21 5.0 MEDIUM 5.3 MEDIUM
When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of large packets requiring fragmentation, generating the following error messages: [LOG: Err] MQSS(0): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[0:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(0): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1838, QID 0 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk length error in stage 5 - Chunk Address: 0x4321f3 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0x0 [LOG: Notice] Error: /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(0), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D430, 18.2X75-D65 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S1 on MX Series; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S4, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.